Department of Safety & Health Training Institute

  • HOME
  • SAFETY
  • HEALTHCARE
  • CONTACT
  • Worker dies after slipping on frost and falling from roof
  • Serious injury after fall from mobile home
  • Hazards of Working from Fixed Ladders
  • Worker falls while dismantling
  • Falls from Heights in Construction
  • Parapet wall collapses
  • Electrician dies after fall
  • Two crab fishers die of hypothermia
  • Worker falls while attempting to change fluorescent lights
  • Secure vehicle against movement
  • Follow manufacturers
  • Check travelling surface
  • Is your mobile ladder stand safe
  • Do not take extension ladders apart
  • Beware of nail and wire framing supports
  • Personal Fall Protection Equipment
  • DOSHTI

    Introduction

    When work is performed on elevated surfaces such as roofs, or during construction activities, protection against falls frequently must be considered. Fall arresting systems, which include lifelines, body harnesses, and other associated equipment, are often used when fall hazards cannot be controlled by railings, floors, nets, and other means. These systems are designed to stop a free fall of up to six feet while limiting the forces imposed on the wearer.

    Scope and Application

    Fall protection is required for most construction activities by the Occupational Safety and Health Administration (OSHA) whenever the work is performed in an area that is six feet higher than its surroundings. Exceptions to this rule include work done from scaffolds, ladders and stairways, derricks and cranes, and work involving electrical transmission and distribution. Also excluded is the performance of inspections, investigations, or assessments of existing conditions prior to the beginning or after the completion of construction.

    Program Description

    Fall protection is required whenever work is performed in an area six feet above its surroundings and can generally be provided through the use of guardrail systems, safety net systems, or personal fall arrest systems. Where it can be clearly demonstrated that the use of these systems is infeasible or creates a greater hazard, a fall protection program that provides for alternative fall protection measures may be implemented.

    Fall Protection Systems

    A variety of systems may be chosen from when providing fall protection. These systems include:

    o Guardrails: Standard guardrails consist of a top rail, located 42 inches above the floor, and a mid-rail. Screens and mesh may be used to replace the mid-rail, so long as they extend from the top rail to the floor.

    o Personal Fall Arresting Systems: Components of a personal fall arresting system include a body harness, lanyard, lifeline, connector, and an anchorage point capable of supporting at least 5000 pounds.

    o Positioning Device Systems: Positioning device systems consist of a body belt or harness rigged to allow work on a vertical surface, such as a wall, with both hands free.

    o Safety Monitoring by a Competent Person: This system allows a trained person to monitor others as they work on elevated surfaces and warn them of any fall hazards.

    o Safety Net Systems: These systems consist of nets installed as close as possible under the work area.

    o Warning Line Systems: Warning line systems are made up of lines or ropes installed around a work area on a roof. These act as a barrier to prevent those working on the roof from approaching it edges.

    o Covers: Covers are fastened over holes in the working surface to prevent falls.


    Additional Precautions

    Protection should also be provided from falling objects. Work surfaces should be kept clear of material and debris by removal at regular intervals. Toe boards should be used to prevent objects from being inadvertently kicked to a lower level. When necessary, canopies should be provided.

    Prohibited Devices

    Body harnesses are required for use with all personal fall arresting systems. Body belt use is prohibited, except under certain specific circumstances. Also, only locking-type snap hooks may be used as part of a fall arresting system.

    Training

    Training must include the following:

    o How to recognize and minimize fall hazards

    o The nature of the fall hazards in the work area

    o Procedures for erecting, maintaining, disassembling, and inspecting the specific fall protection systems used

    o Use, operation, and limitations of fall protection systems

    o The userís role in fall protection systems

    Roles and Responsibilities

    Department

      • Identify areas where fall protection is needed.
      • Obtain or develop fall protection systems.
      • Ensure workers are trained.


    Supervisors

      • Know when fall protection is necessary.
      • Provide workers with fall protection devices.
      • Ensure workers use fall protection devices.


    EHS

      • Assist in identification of areas where fall protection is needed.
      • Provide worker training.


    Individual

      • Attend training.
      • Know when fall protection is necessary.
      • Use fall protection systems.
    Copyright ©2012 All Rights Reserved Doshti.Com
    web counter
    DOSHTI

    Disclaimer:
    This material is for training purpose only to inform the reader of occupational safety and health practice and general compliance requirements.Every effort has been made to ensure complete and accurate information concerning the material presented in the website and course content. However doshti.com or its authors cannot be held legally responsible, or liable for any incidental, indirect, special, or consequential arising out of the course content of the web site or its printing errors.
    These pages does not promote any agenda other than the mutual respect of human beings. The provision of a link in no way endorses the content of any particular website. We believe that exposure to a variety of ideas and beliefs may help increase understanding and mutual respect among the many tribes and cultures of humanity. Therefore a variety of viewpoints are represented.